Zend Server 5.1 install fails with CPF3810...

General discussion on Zend Server for IBM System i
Post Reply
jjcllhn
Posts: 34
Joined: Tue May 05, 2009 7:15 pm

Zend Server 5.1 install fails with CPF3810...

Post by jjcllhn » Tue May 03, 2011 12:22 am

.. while using QSECOFR profile. System value QALWOBJRST='*ALL'.
QGPL/ZSVRSAVF successfully transfers.
QBATCH job to complete installation fails.

I am able to run CRTSAVF QTEMP/QM.0001 using the QSECOFR profile interactively from the command line.

If I try to run RSTLICPGM LICPGM(2ZSVRPI) DEV(*SAVF) OPTION(*BASE) SAVF(QGPL/ZSVRSAVF), the install fails to restore save files PHPMYADMIN, ZENDMYSQL and ZFRAMEWRK to library ZENDSVR

Code: Select all

*NONE      Request                      05/02/11  18:04:19.679648  QWTSCSBJ                 *N       QCMD        QSYS       
                                     Message . . . . :  -RSTLICPGM LICPGM(2ZSVRPI) DEV(*SAVF) OPTION(*BASE)                 
                                       SAVF(QGPL/ZSVRSAVF)                                                                  
CPF3810    Diagnostic              20   05/02/11  18:04:19.969064  QSRRSOBJ     QSYS        122D     QSRRSLIB    QSYS       
                                     Message . . . . :   Save file QM.0001 not restored to library QTEMP.                   
                                     Cause . . . . . :   You do not have sufficient authority to restore a save             
                                       file that does not exist on the system. Recovery  . . . :   Do one of the            
                                       following: 1) Obtain authority to the CRTSAVF command from your security             
                                       officer and use the RSTOBJ command to restore the save file. 2) Have your            
                                       security officer restore the save file.                                              
CPF3770    Escape                  30   05/02/11  18:04:20.107592  QSRROCPR     QSYS        0621     QLPRPCPR    QSYS       
                                     Message . . . . :   No objects saved or restored for library QTEMP.                    
                                     Cause . . . . . :   No objects were saved or restored for library QTEMP at             
                                       05/02/11 18:04:19.   Diagnostic messages have been sent for each error that          
                                       was detected. The objects not restored may include objects that were                 
                                       partially restored and require some additional recovery action. Recovery  .          
                                       . . :   Press F10 or use the Display Job Log (DSPJOBLOG) command for error           
                                       information.  Correct any errors and try the request again.                           
SOLUTION:

Problem is a conflict with third party replication software we are using. RSTLIB command is handled by the replication software rather than the IBM provided RSTLIB (higher in the system library list). Was able to install ZendServer 5.1 from the command line ( RSTLICPGM LICPGM(2ZSVRPI) DEV(*SAVF) OPTION(*BASE) SAVF(QGPL/ZSVRSAVF) ) after removing the third party library- albeit painfully, as any autoresponse message were no longer active for the creation of the IFS directory structure (numerous CPF3DE4 sent to QSYSOPR).

Just in case someone else has a similiar environment. Maybe Zend could consider hard coding the restore operations to reference QSYS/RSTLIB directly.

Post Reply